Seeing flickering lights or a warm outlet? Mt. Juliet Electrical Company handles electrical repairs, panel upgrades, wiring, and installations for homes and businesses across Mt. Juliet and Wilson County. We are available every day from 8:00 AM to 9:30 PM, so you are not left waiting until Monday to get answers on a problem that showed up over the weekend.
Straight answers on the phone. Real electrical work. Quick to respond.
Whether you are a homeowner dealing with a tripped breaker, a landlord keeping a rental up to code, or a property manager coordinating work across multiple units, we handle the full scope of residential and commercial electrical service. Call for a quote and we will walk through what the job involves before anything is scheduled.
We'll take care of the circuits from here.
The hardest part of an electrical problem is knowing when to call, and the honest answer is sooner than most people do. A dead outlet, a breaker that trips every time you run the microwave, or a light that flickers when nothing else is on are all symptoms worth tracing. Left alone, they can point to something minor or something that needs attention before it gets worse.
We troubleshoot the full range of common electrical faults: outlets with no power, breakers that will not hold, burning smells near a panel or outlet, and warm or discolored cover plates. GFCI outlets in bathrooms, kitchens, and garages can trip and cut power to a whole circuit without an obvious cause. AFCI breakers, which protect against arc faults inside walls, can also trip in ways that are hard to diagnose without the right tools. We trace the fault, identify what triggered it, and fix it properly.
We trace the fault. We fix the wiring. We restore the power.
For commercial properties, the same diagnostic approach applies whether it is a retail space, a small office, or a multi-unit building. Prompt response, even for last-minute electrical calls, means you are not waiting days to get a problem looked at when tenants or customers are affected.
We show up ready to work.
Before a small wiring issue turns into a hazard, it is worth getting the right outlets and switches in place. We install standard and GFCI outlets, dimmer switches, and USB-integrated receptacles throughout the home. If a room is short on outlets or the existing ones are worn or sparking, that is a straightforward job that makes a real difference in daily use.
Ceiling fan installation, recessed lighting, and under-cabinet lighting are all common requests, and each one involves more than swapping a fixture. We confirm the circuit can carry the load, run any additional wiring the job requires, and make sure the installation is electrical work done to the standard the next inspection expects.
Outdoor and landscape lighting is a natural fit for Tennessee residential properties, where covered porches, detached garages, and exterior entertaining spaces are common. We wire exterior fixtures, post lights, and pathway lighting with weatherproof connections suited for outdoor use. If a new fixture or fan requires a dedicated circuit rather than sharing an existing one, we handle that as part of the same job.
We'll sort the wiring and clean up after.
Here's what most people get wrong about their wiring: age alone is not always the problem, but the type of wiring and how it was installed can be. Homes built before the 1970s in Wilson County may still have knob-and-tube wiring or aluminum branch circuits, neither of which meets current standards and both of which can create real problems when a home is renovated or sold.
Knob-and-tube replacement and aluminum-wiring remediation are jobs that come up during safety inspections, real estate transactions, and major remodels. We assess what is in the walls, explain what needs to change and why, and carry out the rewiring in a way that brings the affected circuits up to current code. For older homes going through additions or full renovations, whole-home rewiring is sometimes the more practical path, and we scope those jobs on the call so you know what is involved before any work starts.
Proper grounding and bonding are part of every wiring job we do. A circuit that is not correctly grounded creates risk for the equipment connected to it and for the people using it. We do not cut corners on that part of the work.
Dead outlets usually have a simple cause worth finding.
Tennessee's four-season climate puts real demand on a home's electrical system. Summer air conditioning loads, winter heating, and a storm season that brings severe thunderstorms, tornadoes, and occasional ice storms all add up. Mt. Juliet's continued residential growth also means newer homes and additions regularly need panel capacity that matches what is actually being asked of the system. These three services come up consistently in this area, and we handle all of them on the electrical side.
An aging panel, a home addition, a new major appliance, or an EV charger can all push a panel past what it was designed to handle. When breakers trip frequently, when there are no open slots for new circuits, or when a home still has a 100-amp service feeding a modern load, an upgrade is the right move. We perform load calculations to size the new panel correctly, handle the service-entrance work, and coordinate the meter disconnect where required. Subpanel installation for a workshop, garage, or addition is a common companion job. A straightforward choice for homeowners and property managers who need capacity that matches how the property is actually being used.
Wilson County sees its share of storm-related outages, and a properly wired backup generator can keep critical systems running when the grid goes down. The electrical side of a generator installation involves running the dedicated circuit, installing the transfer switch, and connecting the generator to the panel in a way that prevents backfeed onto the utility line. We handle that work correctly so the switch-over is clean and the panel is protected. We do not service the generator unit itself, but the wiring and transfer switch installation are where we come in.
We'll take care of the circuits from here.
A panel-level surge protector does something a power strip cannot: it catches a voltage spike before it reaches any circuit in the house. Tennessee's storm season means grid fluctuations and lightning-related surges are a real and recurring risk. A whole-home device installs at the main panel and protects every outlet, appliance, and connected device in the home at once. It works alongside proper grounding and bonding, which we verify as part of the installation.
You shouldn't have to chase an electrician for answers when you are trying to add a Level 2 charger or a dedicated circuit for a major appliance. We handle both, and the process is the same: assess the panel, confirm capacity, run the circuit, and place the outlet or connection point where it needs to go.
A Level 2 EV charger requires a 240-volt dedicated circuit, typically a 50-amp run from the panel to the garage or driveway. If the panel does not have the capacity, that is something we identify and address as part of the same project. We show up ready to wire, which means the assessment and the installation happen in the same visit when the job allows it.
Dedicated circuits for ranges, dryers, refrigerators, and other high-draw appliances follow the same logic. Sharing a circuit with other loads creates problems over time. A properly sized dedicated circuit removes that risk and keeps the appliance running the way it was designed to.
An electrical inspection covers what is actually in the home: the panel condition, the wiring type, the state of outlets and switches, and whether AFCI and GFCI protection is in place where it is required. For landlords and property managers, an inspection is a practical way to document the condition of a unit before a tenancy or after a complaint. For homeowners buying or selling, it surfaces issues before they become negotiating problems.
You get a straight answer about the work before it is scheduled. We go through what the inspection covers on the call, confirm what we are looking at, and follow up with a clear account of what we found and what, if anything, needs attention.
Pricing for electrical work depends on what the job actually involves, and the only way to give you an accurate number is to understand the scope first. When you call, describe what you are dealing with or what you need installed. We ask the right questions, give you a price for the work, and schedule from there.
There are no vague estimates followed by surprises later. The price is confirmed before anything is scheduled, and you know what it covers. That applies whether you are calling about a single outlet, a panel upgrade, or a full rewiring project.
We serve Mt. Juliet and the surrounding area, including Lebanon, Watertown, Gladeville, and Old Hickory, along with nearby communities like Hermitage, Donelson, La Vergne, and Smyrna. If you are in Wilson County or just across the county line, call and we will confirm whether your address falls within our service area.
A Level 2 EV charger requires a dedicated 240-volt circuit, typically a 50-amp run from the panel. Whether your panel can support it depends on the panel's current load and available breaker slots. We check the panel first, confirm what is available, and tell you whether an upgrade is needed before any circuit work is scheduled.
Breakers that trip frequently under normal load, a panel with no open slots for new circuits, a fuse box that has not been replaced with a breaker panel, or a 100-amp service feeding a home with modern appliances and an EV charger are all indicators. A load calculation tells us what the panel needs to carry, and we perform that before recommending an upgrade.
The electrical work covers running the dedicated circuit from the panel, installing the transfer switch, and connecting the generator in a way that prevents backfeed onto the utility line. A properly installed transfer switch is a safety requirement, not an optional add-on. We handle the wiring and the transfer switch installation once you have the generator unit.
A burning smell from an outlet or panel, visible sparks, a breaker that trips immediately when reset, or a warm or discolored outlet are all situations that warrant a call without delay. Loss of power to part of the home combined with any of those symptoms makes it more urgent. We are open every day from 8:00 AM to 9:30 PM and take short-notice calls.
If you smell burning or see sparking, turn off the breaker feeding that circuit if it is safe to reach the panel. Do not use the outlet or switch until it has been inspected. If the panel itself smells hot or is making noise, contact your utility to cut power at the meter rather than working inside the panel yourself.
Stay clear of the affected area and call us at (629) 313-9459.
Flickering lights that are not caused by a loose bulb, outlets that are warm to the touch, a panel that buzzes or hums, two-prong ungrounded outlets throughout the home, and wiring that is cloth-wrapped rather than plastic-sheathed are all signs worth investigating. Knob-and-tube and aluminum branch wiring are specific conditions that carry known risks and are worth assessing before a renovation or sale.
A burning smell typically indicates heat at a connection point, which can come from a loose wire, an overloaded circuit, or a failing device. It is not something to wait on. Turn off the breaker feeding that area if it is safe to do so, and call for a diagnostic visit. The source needs to be identified before the circuit is used again.
A switch or outlet that buzzes, crackles, or feels warm under normal use has a connection problem. Loose wiring at a device creates resistance, which generates heat. Over time, that heat can damage the device, the wiring, and the box it sits in. A buzzing outlet is not a nuisance issue, it is a wiring fault that needs to be traced and corrected.
A dead outlet that has no power may have tripped a GFCI elsewhere on the circuit, or it may have a loose connection or a failed device. A warm or discolored outlet points to heat at the connection, which is a wiring issue. Discoloration around the cover plate often means arcing has already occurred. Any of those conditions is worth a diagnostic visit rather than a wait-and-see approach.
We start by asking about the symptoms and what was happening when the problem appeared. On the visit, we test the affected outlets, switches, and circuits with the right tools, trace the circuit back toward the panel, and identify where the fault is occurring. We do not swap parts blindly. The diagnostic work identifies the actual cause before any repair is quoted or started.
It depends on what the underlying condition is. A single outlet that failed because of a loose wire is a straightforward repair. If that outlet is part of a circuit with aluminum wiring, knob-and-tube, or repeated faults, a patch addresses the symptom without the cause. We tell you which situation you are in and what the options are, so you can make an informed decision about how far to take the work.
The most common reason is a condition that was not visible until the work started, such as wiring that needs to be rerouted, a box that has to be replaced, or a circuit that turns out to be aluminum rather than copper. We explain any change in scope before the work expands and confirm the revised cost before continuing. Nothing is added without your knowledge.
If an inspection or a repair visit surfaces a code issue that was already present, we explain what it is, what the current requirement is, and what correcting it involves. We do not require you to address every issue before completing the job you called about, but we do document what we found and give you a clear picture of what the correction would involve if you choose to schedule it.
When you need electrical work handled correctly in Mt. Juliet, Mt. Juliet Electrical Company is ready to help. We are available every day from 8:00 AM to 9:30 PM.
Call (629) 313-9459 to get a quote.
Straight answers on the phone. Real electrical work. Quick to respond.
Electrical problems rarely announce themselves at a convenient time, and the range of work that comes up across a home or commercial property is wide. This table lays out what we handle, who each service fits best, and what is worth knowing before you call. Read through, then reach out for a price on the specific job you have in mind.
| Service Type | Scope of Work | Best For | Worth Knowing |
|---|---|---|---|
| Wiring for Additions & Remodels |
| Homeowners adding square footage or converting a garage, basement, or attic | Additions require a permit and inspection in most cases. We scope the electrical side of the project on the call so you know what is involved before the build starts. |
| Breaker & Fuse Repair |
| Homes where a single circuit or breaker keeps failing | A breaker that trips repeatedly under normal load is pointing at something on the circuit, not just the breaker itself. We check both before recommending a fix. |
| Older-Home Rewiring |
| Homes built before the 1970s in Wilson County undergoing renovation, sale, or inspection | Knob-and-tube and aluminum branch wiring are not automatic emergencies, but both carry known risks that are worth understanding before a renovation or real estate transaction. |
| Dedicated Appliance Circuits |
| Homeowners adding a major appliance or finishing a workspace | Sharing a high-draw appliance with other loads on a circuit creates problems over time. A properly sized dedicated circuit removes that risk from the start. |
| Electrical Repairs & Troubleshooting |
| Any homeowner or property manager dealing with an active electrical symptom | Tracing the fault before replacing parts keeps the repair focused and the cost in line with what the job actually requires. |
| Electrical Panel & Service Upgrades |
| Homes adding an EV charger, a major appliance, or an addition, and older homes still on 100-amp service | Panel upgrades are permitted work in most jurisdictions. We handle the coordination so the installation meets what the next inspection expects. |
| Ceiling Fan Installation |
| Rooms adding a fan where a light fixture currently exists, or where no overhead fixture is present at all | A fan-rated box is required where a ceiling fan is mounted. We confirm the box and the circuit before the install. |
| Lighting Installation |
| Homeowners adding or upgrading interior or exterior lighting | Outdoor fixtures in Tennessee need weatherproof connections suited to the climate. We handle the circuit and the connection point, not just the fixture swap. |
| EV Charger Installation |
| Homeowners adding a Level 2 charger for an electric or plug-in hybrid vehicle | If the panel does not have capacity for a 50-amp circuit, we identify that during the assessment and address it as part of the same project where possible. |
| Outlet & Switch Installation |
| Rooms short on outlets or with outdated or failing devices | GFCI outlets in kitchens, bathrooms, and garages are a code requirement in most installations. We confirm what applies at your address before the work starts. |
| Backup Generator Installation |
| Homeowners in Wilson County preparing for storm-related outages | A transfer switch is a safety requirement, not an optional add-on. It prevents backfeed onto the utility line during an outage. We handle the wiring and switch once you have the generator unit. |
| Whole-Home Surge Protection |
| Any home in an area with frequent storms or grid fluctuations | A panel-level surge protector catches a voltage spike before it reaches any circuit in the house. A power strip does not do the same job. |
| Electrical Safety Inspections |
| Landlords, property managers, and homeowners buying or selling | An inspection documents what is in the home and surfaces issues before they become negotiating problems or tenant complaints. We follow up with a clear account of what we found. |
What causes breakers to trip repeatedly under normal use?
A breaker that trips under normal load is usually telling you one of three things: the circuit is carrying more than it was sized for, there is a fault somewhere on the wiring, or the breaker itself is worn and failing. The right answer depends on what is on the circuit and what the load looks like. We check the circuit and the breaker before recommending a fix, because replacing the breaker when the circuit is the problem just moves the fault somewhere else.
Why do outlets in kitchens, bathrooms, and garages need GFCI protection?
GFCI outlets cut power within milliseconds when they detect a ground fault, which is the condition that causes electric shock near water. Code requires them in kitchens, bathrooms, garages, outdoor locations, and anywhere else where an outlet is near a water source. If a GFCI outlet trips and cuts power to other outlets on the same circuit, that is normal behavior, and the reset button is on the GFCI device itself, not always at the outlet that lost power.
How do I know if my home is ready for added electrical load, like a new appliance or a workshop?
The short answer is that the panel tells you. A panel with no open breaker slots, a 100-amp service feeding a fully loaded home, or a panel that already trips under peak demand does not have much room to grow. We run a load calculation before recommending a panel upgrade or a new circuit, so the answer is based on what the system is actually carrying rather than a guess.
Faults Traced Before Anything Is Replaced
We identify the actual cause of an electrical fault before any repair is quoted or started. Replacing parts without tracing the problem first fixes the symptom, not the fault.
What does flickering or dimming lights usually mean?
Flickering that affects one light is often a loose bulb or a failing fixture. Flickering that affects a whole room or multiple rooms points further back in the circuit, toward a loose connection at a junction box, a failing breaker, or a load on the circuit that is pulling more than the wiring was sized for. Dimming that happens when a large appliance kicks on is common in homes where that appliance is sharing a circuit rather than running on a dedicated one.
When should I call an electrician instead of handling something myself?
Swapping a light bulb or resetting a tripped GFCI is straightforward. Anything that involves opening a panel, running new wiring, replacing a breaker, or working inside a wall is a different matter. The risk is not just shock during the work. Wiring that is not connected correctly creates heat at the connection point, and that heat builds over time without any visible warning until it does not. We handle the work inside the walls and the panel so the result holds up.
How does surge protection at the panel differ from a power strip?
A power strip surge protector covers only the devices plugged into it, and most strip-level devices are rated for relatively small surges. A panel-level surge protector sits at the main panel and intercepts a voltage spike before it reaches any circuit in the house, which means every outlet, appliance, and connected device is covered by a single device with a much higher capacity rating. In an area with active storm seasons, the panel-level device is doing the work that matters.
Code-Compliant Work on Every Job
Whether it is a single outlet or a full panel upgrade, the work is done to the standard the next inspection expects. Permitted work is coordinated where the job requires it.
What are the concerns with aluminum branch wiring in older homes?
Aluminum wiring was used in residential construction through parts of the 1960s and 1970s. It expands and contracts more than copper as it heats and cools, which can loosen connections at outlets, switches, and fixtures over time. Loose connections create resistance, and resistance creates heat. The fix is not always a full rewire. In some cases, CO/ALR-rated devices and proper connection methods address the problem at the device level. We assess what is in the walls and explain the options before recommending a scope.
How long does a panel upgrade typically take?
A straightforward panel replacement on a home that does not need a service entrance upgrade usually takes the better part of a day. A service upgrade that involves the meter base or the utility connection adds time and may require a utility disconnect and reconnect, which we coordinate. We give you a realistic time estimate on the call based on what the job involves, and we confirm the scope before anything is scheduled.
Scope Agreed Before the Panel Is Opened
We confirm what the job involves and what it costs before any work begins. If the scope changes once we are into the work, we explain why and get your go-ahead before continuing.
Is grounding and bonding something I should ask about in an older home?
Yes. Homes built before the 1960s often have two-prong ungrounded outlets and wiring that was never run with a ground conductor. A circuit that is not correctly grounded creates risk for the equipment connected to it and for the people using it. Grounding and bonding are part of every wiring job we do, and an inspection of an older home will surface whether the existing system has gaps that need to be addressed.
What is involved in adding a circuit for a basement or sump pump?
A sump pump needs its own dedicated circuit so it is not competing with other loads during a storm when it is working hardest. The circuit run goes from the panel to the pump location, sized for the pump's draw. If the panel does not have an open slot, that is part of the conversation before the work starts. We confirm the panel capacity, run the circuit, and place the outlet where the pump connects.
How does pricing work, and when do I get a number?
You get a price when you call, before anything is scheduled. We ask about the job, work through the scope with you, and give you a clear number for the work. If something changes once the work is underway because of a condition that was not visible at the start, we explain what changed and confirm the revised cost before continuing. Nothing is added without your knowledge.
Call (629) 313-9459 to talk through the job and get a price before anything is scheduled. We are available every day from 8:00 AM to 9:30 PM.
(629) 313-9459